manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1209

www.ti.com

GPIO Registers

1209

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

General-Purpose Input/Outputs (GPIOs)

17.5.6 GPIOIM Register (Offset = 0x410) [reset = 0x0]

GPIO Interrupt Mask (GPIOIM)

The GPIOIM register is the interrupt mask register. Setting a bit in the GPIOIM register allows interrupts
that are generated by the corresponding pin to be sent to the interrupt controller on the combined interrupt
signal. Clearing a bit prevents an interrupt on the corresponding pin from being sent to the interrupt
controller. All bits are cleared by a reset.

GPIOIM is shown in

Figure 17-10

and described in

Table 17-12

.

Return to

Summary Table

.

Figure 17-10. GPIOIM Register

31

30

29

28

27

26

25

24

RESERVED

R-0x0

23

22

21

20

19

18

17

16

RESERVED

R-0x0

15

14

13

12

11

10

9

8

RESERVED

DMAIME

R-0x0

R/W-0x0

7

6

5

4

3

2

1

0

IME

R/W-0x0

Table 17-12. GPIOIM Register Field Descriptions

Bit

Field

Type

Reset

Description

31-9

RESERVED

R

0x0

8

DMAIME

R/W

0x0

GPIO µDMA Done Interrupt Mask Enable

0x0 = The µDMA done interrupt is masked and does not cause an
interrupt.

0x1 = The µDMA done interrupt is not masked and can generate an
interrupt to the interrupt controller.

7-0

IME

R/W

0x0

GPIO Interrupt Mask Enable

0x0 = The interrupt from the corresponding pin is masked.

0x1 = The interrupt from the corresponding pin is sent to the
interrupt controller.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands