manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1547

www.ti.com

QSSI Registers

1547

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Quad Synchronous Serial Interface (QSSI)

23.5.7 SSIRIS Register (Offset = 0x18) [reset = 0x8]

QSSI Raw Interrupt Status (SSIRIS), offset 0x018

The SSIRIS register is the raw interrupt status register. On a read, this register gives the current raw
status value of the corresponding interrupt prior to masking. A write has no effect.

SSIRIS is shown in

Figure 23-16

and described in

Table 23-12

.

Return to

Summary Table

.

Figure 23-16. SSIRIS Register

31

30

29

28

27

26

25

24

RESERVED

R-0x0

23

22

21

20

19

18

17

16

RESERVED

R-0x0

15

14

13

12

11

10

9

8

RESERVED

R-0x0

7

6

5

4

3

2

1

0

RESERVED

EOTRIS

DMATXRIS

DMARXRIS

TXRIS

RXRIS

RTRIS

RORRIS

R-0x0

R-0x0

R-0x0

R-0x0

R-0x1

R-0x0

R-0x0

R-0x0

Table 23-12. SSIRIS Register Field Descriptions

Bit

Field

Type

Reset

Description

31-7

RESERVED

R

0x0

6

EOTRIS

R

0x0

End of Transmit Raw Interrupt Status. This bit is cleared when a 1 is
written to the EOTIC bit in the SSI Interrupt Clear (SSIICR) register.

0x0 = No interrupt.

0x1 = The transmit FIFO is empty, and the last bit has been
transmitted out of the serializer.

5

DMATXRIS

R

0x0

QSSI Transmit DMA Raw Interrupt Status. This bit is cleared when a
1 is written to the DMATXIC bit in the SSI Interrupt Clear (SSIICR)
register.

0x0 = No interrupt.

0x1 = The transmit DMA has completed.

4

DMARXRIS

R

0x0

QSSI Receive DMA Raw Interrupt Status. This bit is cleared when a
1 is written to the DMARXIC bit in the SSI Interrupt Clear (SSIICR)
register.

0x0 = No interrupt.

0x1 = The receive DMA has completed.

3

TXRIS

R

0x1

QSSI Transmit FIFO Raw Interrupt Status. This bit is cleared when
the transmit FIFO is more than half full.

0x0 = No interrupt.

0x1 = T he transmit FIFO is half empty or less.

2

RXRIS

R

0x0

QSSI Receive FIFO Raw Interrupt Status. This bit is cleared when
the receive FIFO is less than half full.

0x0 = No interrupt.

0x1 = The receive FIFO is half full or more.

1

RTRIS

R

0x0

QSSI Receive Time-Out Raw Interrupt Status. This bit is cleared
when a 1 is written to the RTIC bit in the SSI Interrupt Clear
(SSIICR) register.

0x0 = No interrupt.

0x1 = The receive time-out has occurred.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands