manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 493

www.ti.com

HIB Registers

493

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Hibernation Module

6.5

HIB Registers

Table 6-2

lists the memory-mapped registers for the HIB. All register offset addresses not listed in

Table 6-2

should be considered as RESERVED locations and the register contents should not be

modified.

All addresses given are relative to the Hibernation Module base address at 0x400FC000 (ending address
of 0x400FCFFF). The system clock to the Hibernation module must be enabled before the registers can
be programmed (see

Section 4.2.90

). There must be a delay of 3 system clocks after the Hibernation

module clock is enabled before any Hibernation module registers are accessed. In addition, the CLK32EN
bit in the HIBCTL register must be set before accessing any other Hibernation module register.

NOTE:

Except for the HIBIO and a portion of the HIBIC register, all other Hibernation module

registers are on the Hibernation module clock domain and have special timing requirements.
Software should make use of the WRC bit in the HIBCTL register to ensure that the required
timing gap has elapsed. If the WRC bit is clear, any attempted write access is ignored (see

Section 6.3.1

). The HIBIO register and bits RSTWK, PADIOWK, and WC of the HIBIC

register do not require waiting for write to complete. Because these registers are clocked by
the system clock, writes to these registers and bits are immediate.

Writing to registers other than the HIBCTL and HIBIM before the CLK32EN bit in the HIBCTL
register has been set may produce unexpected results.

NOTE:

The Hibernation module registers are reset under two conditions:

1.

Any type of system reset (if the RTCEN and the PINWEN bits in the HIBCTL register are
clear and the TPEN bit in the HIBTPCTL register is clear).

2.

A cold POR occurs when both the V

DD

and V

BAT

supplies are removed.

Any other reset condition is ignored by the Hibernation module.

The following registers can be accessed only through privileged mode (see

Chapter 4

for more details) :

•

HIBTPCTL

•

HIBPTSTAT

•

HIBTPIO

•

HIBTPLOG

•

Upper eight words of memory (HIBDATA register 0x50 to 0x6F)

Table 6-2. HIB Registers

Offset

Acronym

Register Name

Section

0x0

HIBRTCC

Hibernation RTC Counter

Section 6.5.1

0x4

HIBRTCM0

Hibernation RTC Match 0

Section 6.5.2

0xC

HIBRTCLD

Hibernation RTC Load

Section 6.5.3

0x10

HIBCTL

Hibernation Control

Section 6.5.4

0x14

HIBIM

Hibernation Interrupt Mask

Section 6.5.5

0x18

HIBRIS

Hibernation Raw Interrupt Status

Section 6.5.6

0x1C

HIBMIS

Hibernation Masked Interrupt Status

Section 6.5.7

0x20

HIBIC

Hibernation Interrupt Clear

Section 6.5.8

0x24

HIBRTCT

Hibernation RTC Trim

Section 6.5.9

0x28

HIBRTCSS

Hibernation RTC Sub Seconds

Section 6.5.10

0x2C

HIBIO

Hibernation IO Configuration

Section 6.5.11

0x30 to 0x6F HIBDATA

Hibernation Data

Section 6.5.12

0x300

HIBCALCTL

Hibernation Calendar Control

Section 6.5.13

0x310

HIBCAL0

Hibernation Calendar 0

Section 6.5.14

0x314

HIBCAL1

Hibernation Calendar 1

Section 6.5.15

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands