manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual, Page: 503 / 1817

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 503

www.ti.com

HIB Registers

503

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Hibernation Module

Table 6-8. HIBIM Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

3

EXTW

R/W

0x0

External Wake-Up Interrupt Mask

0x0 = The EXTW interrupt is suppressed and not sent to the
interrupt controller.

0x1 = An interrupt is sent to the interrupt controller when the EXTW
bit in the HIBRIS register is set.

2

LOWBAT

R/W

0x0

Low Battery Voltage Interrupt Mask

0x0 = The LOWBAT interrupt is suppressed and not sent to the
interrupt controller.

0x1 = An interrupt is sent to the interrupt controller when the
LOWBAT bit in the HIBRIS register is set.

1

RESERVED

R

0x0

0

RTCALT0

R/W

0x0

RTC Alert 0 Interrupt Mask

0x0 = The RTCALT0 interrupt is suppressed and not sent to the
interrupt controller.

0x1 = An interrupt is sent to the interrupt controller when the
RTCALT0 bit in the HIBRIS register is set.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments