Mova D506i User Manual Download Page 37 | Manualshive

Page: 37 / 644

background image

35

Checks

Before

Use

1

Recharging the mova

Recharging

the

m

ova

•

Use the D014 type battery.

•

The battery will gradually wear out. Each time it is recharged, it will accept slightly less charge than the
previous time. When the battery charge lasts only half as long as when it was new, replace it with a new
one. The battery will wear out after about one year’s use. Note that depending on how often the phone is
used battery life may become shorter.

Notes about the battery

When the battery level gets low, recharge it.

•

The battery level icon shows how much charge remains in the battery.

Continuous call time is measured at maximum transmission power with the battery saving mode off.
Continuous standby time is measured while moving with the mova closed and with good signal
conditions. Call time and standby time may be halved, depending on the amount of charge in the
battery, the function selected, the ambient temperature and signal strength (i.e. when there is no signal
or the signal is weak). If you use i-mode communication and i-shot transmission, the call/communication
time and standby time will be shorter. Even if you do not make a call or use i-mode and send i-shot, the
call/communication time and standby time will also be shorter when composing i-mode mail, taking or
editing picture or running a downloaded i-

α

ppli application. Note that some i-

α

ppli applications may

perform communication after downloading. You can set your mova beforehand to disable such
connections.

•

When “continual light” is set in the setting during recharging of the Light setting, recharging will take
longer with the mova turned on. If left as it is after the completion of recharging, the battery level gets
low and recharging is started after a certain period of time.

: Fully charged.

: Partially charged.

: Almost completely discharged. Recharge the battery.

Current remaining battery level

Recharge time and Battery use tim estimates

Recharge time

Continuous call/communication time

Continuous standby time

Approx. 120 minutes

Approx. 135 minutes

Approx. 500 hours

«
...
35
36
37
38
39
...
»

Summary of Contents for D506i





































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for D506i

Brand: Yealink Pages: 229

Brand: i.safe MOBILE Pages: 21

Brand: Fysic Pages: 8

Brand: Profoon Pages: 56

Brand: Wistec Pages: 60

Brand: TCL Pages: 62

Brand: snopfon Pages: 46

Brand: Xiaomi Pages: 52

Brand: AEG Pages: 224

Brand: LOBSTER Pages: 75

Brand: Zte Pages: 36

Brand: Zte Pages: 65

Brand: Zte Pages: 33

Brand: Avvio Pages: 46

MULTI CLIP A200

Brand: Samsung Pages: 4

Brand: Samsung Pages: 31

SGH-A767 Series

Brand: Samsung Pages: 44

Gear Fit SM-R350

Brand: Samsung Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands