Mova D506i User Manual Download Page 40 | Manualshive

Page: 40 / 644

Mova D506i User Manual Download Page 40

38

Checks

Before

Use

1

Battery

Level

Checking the Remaining Battery Level

Battery Level

You can check the current battery level.

1

Turn on the mova.

The battery level icon appears.

: Fully charged

: Partially charged

: Almost completely discharged Charging is required

•

Turning the power on/off (see p.39)

Battery level icon
The icon also appears on the Inspiration window

Using sound and display to check the remaining battery level

You can use the sound and/or display to check the remaining battery level.

•

When the battery level icon is not shown at times such as immediately after the power is turned
on, the remaining battery level cannot be checked.

•

The battery level icon is a guide to how much charge remains.

1

In standby or during a call, select “setting”

“cost

•

check”

“battery level”

from the menu.

The remaining battery level appears.

Fully charged

(Beeps three times)

Partially charged

(Beeps twice)

Recharge the battery.

Almost completely discharged

(Beeps once)

▲

▲

•

In the following cases, however, no beeps sound:

•

In the Manner mode

•

In the Drive mode

•

When Keypad Sound is off.

•

When the battery nearly runs down, the message “charge battery” appears in the main display or the
Inspiration window, an alarm sounds, and after a minute or so the power goes off. (To stop alarm, press

.) During a call, an alarm sounds, and after about 20 seconds the call ends.

N o t e

M4 15

▲

«
...
38
39
40
41
42
...
»

Summary of Contents for D506i





































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands