![Mova D506i User Manual Download Page 301](http://html.mh-extra.com/html/mova/d506i/d506i_user-manual_1841068301.webp)
299
Using
i-mode
to
G
et
Information
i-mode
S
ettings
12
i-mode Settings
Making i-mode Settings
•
If you set other than “answer”, the ringtone sounds and the following screen appears when there is an
incoming call during i-mode communication or in i-mode standby.
•
When Call Reception during i-mode is set to “answer,” incoming calls interrupt mail and Message
downloads. Perform the Check New Message operation after the call to receive mail and Messages that
could not be received.
•
During i-mode communication or in i-mode standby, there may be a delay between when an incoming call
is received and when the designated ringtone and call reception screen are triggered. The caller is notified
of this delay.
•
In Drive Mode, you cannot receive a call even if you have set “answer”. The ringtone does not sound, “call
in packet” is displayed, and the call is recorded in the Call history.
•
If you select “voice mail”, “forward w/ MSG” or “forward w/o MSG” when you do not subscribe to the Voice
Mail Service or Call Forwarding Service, during i-mode communication or in i-mode standby, callers hear
the beginning of the announcement since the call is cut off midway. The message “call in packet” appears
on the screen.
•
While Reject Calls, Accept Calls, Caller ID-based Call Block, or Reject Unstored Number is set, no ringtone
sounds for calls received from a party for which call rejection is set during i-mode communication or in
i-mode standby. The message “call in packet” appears and the call is recorded in the Call history. The
caller hears the same announcement as for the “notification” setting.
•
If you receive a call to a Number Plus telephone number during i-mode communication or in i-mode
standby, the caller hears a busy signal regardless of your Call Reception setting during i-mode, and you
cannot answer the call.
N o t e
[Set Call Reception during i-mode]
Receiving calls while using i-mode
You can use the standard procedure for answering calls (press
) to answer calls
during i-mode communication or in i-mode standby.
You can also set your mova to not receive incoming calls during i-mode communication or
in i-mode standby.
[Default] answer
1
In standby, select “i-mode setting”
“set reception” from the i-mode menu.
•
Alternatively, you can select “setting”
“i-mode setting” from the menu.
•
You can also select “i-mode STNG” from the submenu while displaying a site, Screen memo, or
a Message.
2
Select a handling method for incoming calls and press
(select).
The Call Reception setting during i-mode is changed.
•
To answer calls even during i-mode communication or in i-mode standby, select “1. answer”. To
not receive calls during i-mode communication or in i-mode standby, select one of the
commands from “2. notification” to “5. forward w/o MSG”. For details, see p.300.
▲
▲
•
The name or reading is displayed for a party stored in the phonebook. The reason for
caller ID anonymity is indicated for a party without a caller ID (see p.72).
•
If the Keypad Lock or Phonebook Access Lock is set when a call is received from a
party listed in the Phonebook, the other party’s name, etc. does not appear. When a
party is stored in Secret memory, the name is not displayed either.
•
When you press
(OK) or about 5 minutes elapse without performing any
operation, the screen returns to the previous screen.
M8 21
/
M4 51
▲
▲
Summary of Contents for D506i
