Dell Networking S6000 System Reference Manual Download

Page: 82 / 1510

The total amount of space allowed is 16 FP Blocks. System flow requires three
blocks and these blocks cannot be reallocated. The

ipv4acl

profile range is from

1 to 4.

When configuring space for IPv6 ACLs, the total number of Blocks must equal 13.

Ranges for the CAM profiles are from 1 to 10, except for the

ipv6acl

profile which

is from 0 to 10. The

ipv6acl

allocation must be a factor of 2 (2, 4, 6, 8, 10).

If you enabled BMP 3.0, to perform a reload on the chassis to upgrade any
configuration changes that have changed the NVRAM content, use the

reload

conditional nvram-cfg-change

command.

clear line

Reset a terminal line.

S6000

Syntax

clear line {

line-number

| aux 0 | console 0 |

vty number

}

Parameters

line-number

Enter a number for one of the 12 terminal lines on the
system. The range is from 0 to 11.

aux 0

Enter the keywords

aux 0

to reset the auxiliary port.

console 0

Enter the keywords

console 0

to reset the console port.

vty number

Enter the keyword

vty

then a number to clear a terminal

line. The range is from 0 to 9.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Control and Monitoring

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands