Dell Networking S6000 System Page 762 Reference Manual Download

Page: 762 / 1510

ip-address

(OPTIONAL) Specify a name of a device or the IP address of
the device to view more detailed information about the
route.

mask

(OPTIONAL) Specify the network mask of the route. Use this
parameter with the IP address parameter.

longer-prefixes

(OPTIONAL) Enter the keywords

longer-prefixes

to view

all routes with a common prefix.

list

prefix-list

(OPTIONAL) Enter the keyword

list

and the name of a

configured prefix list. For more information, refer to the

show ip route list

command.

protocol

(OPTIONAL) Enter the name of a routing protocol (

bgp

isis

ospf

rip

) or the keywords connected or static.

NOTE:

bgp

isis

ospf

, and

rip

• If you enter

bgp

, you can include the BGP

as-number

• If you enter

isis

, you can include the ISIS

routing-

tag

• If you enter

ospf

, you can include the OSPF

process-

process-id

(OPTIONAL) Specify that only OSPF routes with a certain
process ID must be displayed.

routing-tag

(OPTIONAL) Specify that only ISIS routes with a certain
routing tag must be displayed.

connected

(OPTIONAL) Enter the keyword

connected

to view only the

directly connected routes.

all

(OPTIONAL) Enter the keyword

all

to view both active and

non-active routes.

static

(OPTIONAL) Enter the keyword

static

to view only routes

the

ip route

command configures.

summary

(OPTIONAL) Enter the keyword

summary

. For more

information, refer to the

show ip route summary

command.

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.4.
(0.0)

Added support for VRF.

762

IPv4 Routing

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands