manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 895 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 895

If you disable FEFD globally (

no fefd-global

), the system does not remove the 

FEFD interface configuration.

Related 
Commands

•

fefd

 — enables far-end failure detection.

•

fefd-global interval

 — configures an interval between FEFD control packets.

•

show fefd

 — shows the FEFD command output.

show fefd

View FEFD status globally or on a specific interface.

S6000

Syntax

show fefd [

interface

]

Parameters

interface

(OPTIONAL) Enter the following keywords and slot/port or 
number information:

• For a 10-Gigabit Ethernet interface, enter the keyword 

TenGigabitEthernet

 then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword 

fortyGigE

 then the slot/ port information.

Command 
Modes

• EXEC
• EXEC Privilege

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 
8.3.12.0

Introduced on the S4810.

Legacy E-
Series 
command.

Usage 
Information

The following describes the 

show fefd

 command shown in the following 

example.

Layer 2

895

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments