manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual

Introducing the Dell Networking S6000 System, a cutting-edge networking solution offering exceptional performance and scalability. Explore the device's full potential with our comprehensive Test Report and user-friendly manual, available for free download from our website. Unleash the power of Dell Networking S6000 System today!

Share
Download
background image

26

Intermediate System to Intermediate 

System (IS-IS)

The intermediate system to intermediate system (IS-IS) protocol for IPv4 and IPv6 is supported on the 
S6000platform.
IS-IS is an interior gateway protocol that uses a shortest-path-first algorithm. IS-IS facilitates the 
communication between open systems, supporting routers passing both IP and OSI traffic.

A router is considered an intermediate system. Networks are partitioned into manageable routing 
domains, called areas. Intermediate systems send, receive, and forward packets to other routers within 
their area (Level 1 and Level 1-2 devices). Only Level 1-2 and Level 2 devices communicate with other 
areas.

IS-IS protocol standards are listed in the Standard Compliance chapter in the 

Dell Networking OS 

Configuration Guide

.

NOTE: The fundamental mechanisms of IS-IS are the same between IPv4 and IPv6. Where there are 

differences between the two versions, they are identified and clarified in this chapter. Except where 

identified, the information in this chapter applies to both protocol versions.

adjacency-check

Verify that the “protocols supported” field of the IS-IS neighbor contains matching values to this router.

S6000

Syntax

adjacency-check

To disable adjacency check, use the 

no adjacency-check

 command.

Defaults

Enabled.

Command 
Modes

• ROUTER ISIS (

for IPv4

)

• CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (

for IPv6

)

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

788

Intermediate System to Intermediate System (IS-IS)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Qlogic SANbox 5802V User Manual preview
SANbox 5802V
Brand: Qlogic Pages: 135
Qlogic SANbox2 SANbox2-64 User Manual preview
SANbox2 SANbox2-64
Brand: Qlogic Pages: 224
Cross Technologies 1582-225L2 Instruction Manual preview
1582-225L2
Brand: Cross Technologies Pages: 20
IMC Networks iMcV-Giga-FiberLinX-II Operation Manual preview
iMcV-Giga-FiberLinX-II
Brand: IMC Networks Pages: 60
Top View KVM-102U User Manual preview
KVM-102U
Brand: Top View Pages: 2
N-Tron 714FX6 Series User Manual & Installation Manual preview
714FX6 Series
Brand: N-Tron Pages: 158
GE POWER/VAC 4.16 Instructions Manual preview
POWER/VAC 4.16
Brand: GE Pages: 50
Festo CRSMEO-4 Series Operating Instructions Manual preview
CRSMEO-4 Series
Brand: Festo Pages: 16
Conceptronic HUBBIES 01 Multi Language Quick Manual preview
HUBBIES 01
Brand: Conceptronic Pages: 7
3Com 3CB9E7 - CoreBuilder 9000 Chassis Switch Getting Started Manual preview
3CB9E7 - CoreBuilder 9000 Chassis Switch
Brand: 3Com Pages: 132
Global Streams GlobeCaster STUDIO 4000 Manual preview
GlobeCaster STUDIO 4000
Brand: Global Streams Pages: 144
MRD TNM4000-TP36FF4X16G24P User Manual preview
TNM4000-TP36FF4X16G24P
Brand: MRD Pages: 38
Ormazabal velatia cgm.3 system General Instructions Manual preview
velatia cgm.3 system
Brand: Ormazabal Pages: 76
Comprehensive CVG-21RCA User Manual preview
CVG-21RCA
Brand: Comprehensive Pages: 12
Rowley R-TEC Automation RTMWSR15C Manual preview
R-TEC Automation RTMWSR15C
Brand: Rowley Pages: 10
J-TECH JTECH-4K88-EX-RX Operating Instructions Manual preview
JTECH-4K88-EX-RX
Brand: J-TECH Pages: 40
Exsys EX-1195HMS Manual preview
EX-1195HMS
Brand: Exsys Pages: 14
LEGRAND Wattstopper EOSW Series Manual preview
Wattstopper EOSW Series
Brand: LEGRAND Pages: 12

Brands by name

Popular brands

Load more brands