manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 361 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 361

neighbor activate

This command allows the specified neighbor/peer group to be enabled for the current AFI/SAFI (Address 
Family Identifier/Subsequent Address Family Identifier).

S6000

Syntax

neighbor [

ip-address

 | 

peer-group-name

] activate

To disable, use the 

no neighbor [

ip-address

 | 

peer-group-name

] 

activate

 command.

Parameters

ip-address

(OPTIONAL) Enter the IP address of the neighbor in dotted 
decimal format.

peer-group-
name

(OPTIONAL) Enter the name of the peer group.

activate

Enter the keyword 

activate

 to enable the neighbor/peer 

group in the new AFI/SAFI.

Defaults

Disabled

Command 
Modes

CONFIGURATION-ROUTER-BGP-ADDRESS FAMILY

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Usage 
Information

By default, when you create a neighbor/peer group configuration in the Router 
BGP context, this enables IPv4/Unicast AFI/SAFI. When you use 

activate

 in the 

new context, the neighbor/peer group enables for AFI/SAFI.
It is not possible to de-activate a peer from the IPv4 unicast address family.

Border Gateway Protocol

361

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments