Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 1468 / 1510

background image

Default

32768

Command
Modes

VLT DOMAIN

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.2(0.0)

Introduced on the M I/O Aggregator. This command is
supported in Programmable-Mux (PMUX) mode only.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.8.0

Introduced on the S4810.

Usage
Information

After you configure the VLT domain on each peer switch on both sides of the
interconnect trunk, by default, the Dell Networking OS software elects a primary
and secondary VLT peer device. To reconfigure the primary role of VLT peer
switches, use the

priority

command.

show vlt brief

Displays summarized status information about VLT domains currently configured on the switch.

S6000

Syntax

show vlt brief

Default

Not configured.

Command
Modes

EXEC

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.0.0.0

Introduced on the Z9000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.8.0

Introduced on the S4810.

1468

Virtual Link Trunking (VLT)

«
...
1466
1467
1468
1469
1470
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: DANLERS Pages: 2

ProConnect PS2KVM2

Brand: Linksys Pages: 17

Brand: XtendLan Pages: 24

Brand: Ask Pages: 4

MCD-LED17 series

Brand: Raritan Pages: 89

Brand: Avenview Pages: 10

SI1P-SH-DVI-UCAC

Brand: Black Box Pages: 16

Brand: Lockly Pages: 12

Brand: Manhattan Pages: 4

Brand: NETGEAR Pages: 2

Brand: ABM Pages: 8

Chief Kontour KPWR Series

Brand: LEGRAND Pages: 8

Master View CS-102

Brand: ATEN Pages: 11

Brand: Wantec Pages: 4

Brand: Kramer Pages: 2

Brand: Cambium Networks Pages: 29

FS728TP - ProSafe 24 Port 10/100 Smart Switch

Brand: NETGEAR Pages: 261

Brand: Audioplex Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands