Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 1106 / 1510

background image

40

Quality of Service (QoS)

The Dell Networking operating software commands for quality of service (QoS) include traffic

conditioning and congestion control. QoS commands are not universally supported on all Dell
Networking Products.S6000 platform.
This chapter contains the following sections:

•

Global Configuration Commands

•

Per-Port QoS Commands

•

Policy-Based QoS Commands

Global Configuration Commands

There is only one global configuration QoS command.

qos-rate-adjust

By default, while rate limiting, policing, and shaping, Dell Networking OS does not include the Preamble,

SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC

are used for forwarding and are included in these rate metering calculations. You can optionally include

overhead fields in rate metering calculations by enabling QoS Rate Adjustment.

S6000

Syntax

qos-rate-adjustment

overhead-bytes

Parameters

overhead-bytes

Include a specified number of bytes of packet overhead to
include in rate limiting, policing, and shaping calculations.
The range is from 1 to 31.

Defaults

QoS rate adjustment is disabled by default.

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

1106

Quality of Service (QoS)

«
...
1104
1105
1106
1107
1108
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: D-Link Pages: 16

Brand: D-Link Pages: 2

Brand: Hama Pages: 5

SuperStack 3 4900

Brand: 3Com Pages: 2

Brand: Idem Pages: 2

Brand: OEZ Pages: 5

Brand: Handic Pages: 2

Brand: Comtrend Corporation Pages: 2

3C16710 - OfficeConnect 8/TPM Hub

Brand: 3Com Pages: 130

Brand: Taiden Pages: 21

Brand: LINK-MI Pages: 12

Brand: Lancom Pages: 21

Brand: Racal Instruments Pages: 53

Brand: J-Tech Digital Pages: 12

3 x 4 SWITCH PLUS

Brand: W2IIHY Pages: 28

Brand: Orbis Pages: 2

Brand: ATEN Pages: 2

Valena Life LE-752107

Brand: LEGRAND Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands