Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 1428 / 1510

background image

to any IPv4 or IPv6 (depending on the tunnel mode) address configured on the
switch that is operationally

Up

.

tunnel keepalive

Configure the tunnel keepalive target, interval and attempts.

S6000

Syntax

tunnel keepalive {

ip-address | ipv6-address

}[interval

{

seconds

}] [attempts {

count

| unlimited}]

To disable the tunnel keepalive probes use the

no

tunnel keepalive

command.

Parameters

ip-address ipv6
address

Enter the

IPv4 or IPv6 address

of the peer to which

the keepalive probes will be sent.

interval
seconds

Enter the keyword

interval

then the interval time, in

seconds, after which the restart process to keepalive probe
packets.

The range is from 5 to 255. The default is 5.

count

(OPTIONAL) Enter the keyword

count

to count packets

processed by the filter.

The range is from 3 to 10. The default is 3.

unlimited

Enter the keyword

unlimited

to specify the unlimited

number of keepalive probe packets.

Defaults

Tunnel keepalive is disabled.

Command
Modes

INTERFACE TUNNEL

Command
History

Version 9.4(0.0)

Introduced on the S4810, S4820T, S6000 and Z9000.

Usage
Information

Enabling tunnel keepalive causes ICMP echo packets to be sent to the keepalive
target. The ICMP echo will be sourced from the tunnel interface logical IPv4 or
IPv6 address and will be tunnel encapsulated. The response will be accepted
whether it returns tunnel encapsulated or not.

When configuring tunnel keepalive at both end points of a tunnel interface it is
recommended to set the tunnel keepalive target to the logical IPv4 or IPv6 address

1428

Object Missing

«
...
1426
1427
1428
1429
1430
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: N-Tron Pages: 18

Brand: B&B Electronics Pages: 26

Brand: B&B Electronics Pages: 15

Brand: B&B Electronics Pages: 45

Brand: KELCO Pages: 2

Brand: Jasco Pages: 2

EOC Master CD7944N

Brand: Data Pages: 18

Brand: GarrettCom Pages: 39

SmartStack STS16-20R

Brand: Cabletron Systems Pages: 258

Brand: Optex Pages: 2

Brand: Hall Research Technologies Pages: 9

LMX-2602G-SFP Series

Brand: ANTAIRA Pages: 19

Brand: Black Box Pages: 50

SECURVIEW SV-7020

Brand: CrimeStopper Pages: 1

CESRA PIR 10VDC

Brand: DANLERS Pages: 2

Brand: MiLAN Pages: 13

Brand: ALFAtron Pages: 23

Brand: TRENDnet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands