Dell Networking S6000 System Reference Manual Download Page 985

Page: 985 / 1510

To disable graceful restart mode, use the

no graceful-restart mode

command.

Parameters

planned-only

(OPTIONAL) Enter the keywords

planned-only

to indicate

graceful restart is supported in a planned restart condition
only.

unplanned-
only

(OPTIONAL) Enter the keywords

unplanned-only

indicate graceful restart is supported in an unplanned restart
condition only.

Defaults

Support for both planned and unplanned failures.

Command
Modes

ROUTER OSPF

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version
8.3.12.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

pre-Version
6.1.1.1

Introduced on the E-Series.

graceful-restart role

Specify the role for your OSPF router during graceful restart.

S6000

Syntax

graceful-restart role [helper-only | restart-only]

To disable graceful restart role, use the

no graceful-restart role

command.

Parameters

role helper-
only

(OPTIONAL) Enter the keywords

helper-only

to specify

the OSPF router is a helper only during graceful restart.

role restart-
only

(OPTIONAL) Enter the keywords

restart-only

to specify

the OSPF router is a restart only during graceful-restart.

Open Shortest Path First (OSPFv2 and OSPFv3)

985

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Dell Networking S6000 System, Reference Manual, Page: 985 / 1510

Search results

Summary of Contents for Networking S6000 System

Reviews: