manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 154 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 154

Related 
Commands

dot1x authentication (Configuration)

 — Enable dot1x globally.

dot1x guest-vlan

Configure a guest VLAN for limited access users or for devices that are not 802.1X capable.

S6000

Syntax

dot1x guest-vlan 

vlan-id

To disable the guest VLAN, use the 

no dot1x guest-vlan 

vlan-id

 command.

Parameters

vlan-id

Enter the VLAN Identifier. The range is from 1 to 4094.

Defaults

Not configured.

Command 
Modes

CONFIGURATION (

conf-if-interface-slot/port

)

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.0.0.0

Introduced on the Z9000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 
8.3.12.0

Introduced on the S4810.

Version 8.3.11.1

Introduced on the Z9000.

Version 7.6.1.0

Introduced on the C-Series, E-Series, and S-Series.

Usage 
Information

1X authentication is enabled when an interface is connected to the switch. If the 
host fails to respond within a designated amount of time, the authenticator places 
the port in the guest VLAN.

If a device does not respond within 30 seconds, it is assumed that the device is not 
802.1X capable. Therefore, a guest VLAN is allocated to the interface and 
authentication, for the device, occurs at the next reauthentication interval (

dot1x 

reauthentication

).

154

802.1X

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments