Dell Networking S6000 System Page 1470 Reference Manual Download

Page: 1470 / 1510

HeartBeat Timeout: 3

UDP Port: 34998

HeartBeat Messages Sent: 1026

HeartBeat Messages Received: 1025

show vlt counters

Displays the counter information.

S6000

Syntax

show vlt counters [arp| igmp-snoop | interface | mac | ndp]

Parameters

arp

Enter the keyword

arp

to display the ARP counter

information for the VLT.

igmp-snoop

Enter the keywords

igmp-snoop

to display the igmp-

snooping counter information for the VLT.

interface

Enter the keyword

interface

to display the interface

counter information for the VLT.

mac

Enter the keyword

mac

to display the MAC address counter

information for the VLT.

ndp

Enter the keyword

ndp

to display the VLT counter

information for NDP.

Default

Not configured.

Command
Modes

EXEC

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.0.0.0

Introduced on the Z9000.

Version
8.3.19.0

Introduced on the S4820T.

Version
8.3.12.0

Introduced on the S4810.

Usage
Information

If you do not add a parameter such as

arp

mac

, the output displays all of the

counters.

Example

Dell# show vlt counter

Total VLT counters

1470

Virtual Link Trunking (VLT)

«
...
1468
1469
1470
1471
1472
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands