Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 208 / 1510

background image

When you use the

log

option, the CP processor logs details about the packets that

match. Depending on how many packets match the log entry and at what rate, the
CP may become busy as it has to log these packets’ details.

If you configure the

sequence-number

, the

sequence-number

is used as a tie

breaker for rules with the same order.

NOTE: When ACL logging and byte counters are configured simultaneously,
byte counters may display an incorrect value. Configure packet counters with
logging instead.

Related
Commands

— configures a filter to drop packets.

— configures a filter to forward packets.

Common MAC Access List Commands

The following commands are available within both MAC ACL modes (Standard and Extended) and do not
have mode-specific options. These commands allow you to clear, display, and assign MAC ACL
configurations.

The S6000 supports both Ingress and Egress MAC ACLs.

The MAC ACL can be applied on Physical, Port-channel and VLAN interfaces. As per the specified rules in
the acl, the traffic on the interface/ VLAN members or Port-channel members will be permitted or
denied.

clear counters mac access-group

Clear counters for all or a specific MAC ACL.

S6000

Syntax

clear counters mac access-group [

mac-list-name

]

Parameters

mac-list-name

(OPTIONAL) Enter the name of a configured MAC access list.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

208

Access Control Lists (ACL)

«
...
206
207
208
209
210
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: KE2 Pages: 4

Brand: SIMON RWA Pages: 3

Brand: Kramer Pages: 2

Brand: ADDER Pages: 46

Brand: Vector Pages: 6

Brand: Mellanox Technologies Pages: 12

DL-DVI-MUX2-NT SERIES

Brand: G&D Pages: 76

Sierra Video 1208V3S

Brand: Kramer Pages: 2

FlowPoint 2100 12

Brand: Cabletron Systems Pages: 36

Brand: Hawking Pages: 2

Brand: Woxcon Pages: 42

Brand: Fairchild Pages: 20

Brand: Manhattan Pages: 2

Brand: Pathway connectivity solutions Pages: 34

Brand: S&S Northern Pages: 8

velatia cgm.3 system

Brand: Ormazabal Pages: 76

Brand: DX Engineering Pages: 4

Brand: H3C Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands