Dell Networking S6000 System Reference Manual Download

Page: 681 / 1510

Line

Description

Voltage High
Alarm Flag

This can be either true or false, depending on the Current
Temperature value displayed above.

Tx Bias High
Alarm Flag

This can be either true or false, depending on the present Tx
bias current value displayed above.

Tx Power High
Alarm Flag

This can be either true or false, depending on the Current Tx
bias power value displayed above.

Rx Power High
Alarm Flag

This can be either true or false, depending on the Current Rx
power value displayed above.

Temperature Low
Alarm Flag

This can be either true or false, depending on the Current
Temperature value displayed above.

Voltage Low
Alarm Flag

This can be either true or false, depending on the Current
voltage value displayed above.

Tx Bias Low Alarm
Flag

This can be either true or false, depending on the Tx bias
current value displayed above.

Tx Power Low
Alarm Flag

This can be either true or false, depending on the Current Tx
power value displayed above.

Rx Power Low
Alarm Flag

This can be either true or false, depending on the Current Rx
power value displayed above.

Temperature High
Warning Flag

This can be either true or false, depending on the Current
Temperature value displayed above.

Voltage High
Warning Flag

This can be either true or false, depending on the Current
Voltage value displayed above.

Tx Bias High
Warning Flag

This can be either true or false, depending on the Tx bias
current value displayed above.

Tx Power High
Warning Flag

This can be either true or false, depending on the Current Tx
power value displayed above.

Rx Power High
Warning Flag

This can be either true or false, depending on the Current Tx
power value displayed above.

Temperature Low
Warning Flag

This can be either true or false, depending on the Current
Temperature value displayed above.

Voltage Low
Warning Flag

This can be either true or false, depending on the Current
Voltage value displayed above.

Tx Bias Low
Warning Flag

This can be either true or false, depending on the present Tx
bias current value displayed above.

Tx Power Low
Warning Flag

This can be either true or false, depending on the Current Tx
power value displayed above.

Rx Power Low
Warning Flag

This can be either true or false, depending on the Current Rx
power value displayed above.

Interfaces

681

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands