Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 1189 / 1510

background image

42

Remote Monitoring (RMON)

The Dell Networking operating software remote monitoring (RMON) is implemented on the S6000
platform.
Dell Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and
long-term statistics collection. Dell Networking OS RMON supports the following RMON groups, as
defined in RFC-2819, RFC-3273, and RFC-3434:

• Ethernet Statistics Table; RFC-2819
• Ethernet Statistics High-Capacity Table; RFC-3273, 64bits
• Ethernet History Control Table; RFC-2819
• Ethernet History Table; RFC-2819
• Ethernet History High-Capacity Table; RFC-3273, 64bits
• Alarm Table; RFC-2819
• High-Capacity Alarm Table (64bits); RFC-3434, 64bits
• Event Table; RFC-2819
• Log Table; RFC-2819

Dell Networking OS RMON does not support the following statistics:

• etherStatsCollisions
• etherHistoryCollisions
• etherHistoryUtilization

NOTE: Only SNMP GET/GETNEXT access is supported. Configure RMON using the RMON

commands. Collected data is lost during a chassis reboot.

rmon alarm

Set an alarm on any MIB object.

S6000

Syntax

rmon alarm

number variable interval

{delta | absolute} rising-

threshold

value event-number

falling-threshold

value event-

number

[owner

string

]

To disable the alarm, use the

no rmon alarm

number

command.

Parameters

number

Enter the alarm integer number from 1 to 65535. The value
must be unique in the RMON alarm table.

Remote Monitoring (RMON)

1189

«
...
1187
1188
1189
1190
1191
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

D-PFS4226-24ET-240

Brand: Dahua Pages: 58

Brand: N-Tron Pages: 2

Brand: AVLT-Power Pages: 12

Brand: KCC Pages: 6

Brand: Icy Box Pages: 6

SmartSwitch 2500

Brand: Cabletron Systems Pages: 402

UltraHD Switch 3:1

Brand: Oehlbach Pages: 20

IPES-5222T Series

Brand: Lantech Pages: 30

Hi-Speed USB 4-Port Bay Hub

Brand: SIIG Pages: 8

Brand: H3C Pages: 70

Brand: Planet Pages: 2

EXT-HDMI-CAT5-844

Brand: Gefen Pages: 28

Brand: CYP Pages: 20

Brand: Black Box Pages: 44

Brand: IBM Pages: 94

Brand: B&B Electronics Pages: 2

RPT-2012/P-4F-T-1 Series

Brand: Subject Link Pages: 2

ConferenceHub TA-6500

Brand: TeleAdapt Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands