Dell Networking S6000 System Page 1383 Reference Manual Download

Page: 1383 / 1510

Message ID

Trap Type

Trap Option

%CHMRG-5-MINOR_TEMP_CLR: Minor alarm cleared:
chassis temperature normal (%s %d temperature is
within threshold of %dC)

CHM_MAJ_ALRM_TEMP

ENVMON

TEMP

%CHMGR-2-MAJOR_TEMP: Major alarm: chassis
temperature high (%s temperature reaches or exceeds
threshold of %dC)

CHM_MAJ_ALRM_TEMP_CLR

ENVMON

TEMP

%CHMGR-2-MAJOR_TEMP_CLR: Major alarm cleared:
chassis temperature lower (%s %d temperature is
within threshold of %dC)

CHM_FANTRAY_BAD

ENVMON

FAN

For E1200: %CHMGR-2-FAN_TRAY_BAD: Major alarm: fan

tray %d is missing or down

%CHMGR-2-ALL_FAN_BAD: Major alarm: all fans in fan

tray %d are down.

For E600 and E300: %CHMGR-2-FANTRAYBAD: Major

alarm: fan tray is missing

%CHMGR-2-FANSBAD: Major alarm: most or all fans in

fan tray are down

CHM_FANTRAY_BAD_CLR

ENVMON

FAN

For the E1200: %CHMGR-5-FAN_TRAY_OK: Major alarm

cleared: fan tray %d present

For the E600 and E300: %CHMGR-5-FANTRAYOK: Major

alarm cleared: fan tray present

CHM_MIN_FANBAD

ENVMON

FAN

For the E1200: %CHMGR-2-FAN_BAD: Minor alarm: some

fans in fan tray %d are down

For the E600 and E300: %CHMGR- 2-1FANBAD: Minor

alarm: fan in fan tray is down

CHM_MIN_FANBAD_CLR

ENVMON

FAN

For E1200: %CHMGR-2-FAN_OK: Minor alarm cleared:

all fans in fan tray %d are good

For E600 and E300: %CHMGR-5-FANOK: Minor alarm

cleared: all fans in fan tray are good

TME_TASK_SUSPEND

ENVMON

NONE

%TME-2-TASK SUSPENDED: SUSPENDED - svce:%d - inst:
%d - task:%s

TME_TASK_TERM

ENVMON

NONE

SNMP Traps

1383

«
...
1381
1382
1383
1384
1385
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands