Dell Networking S6000 System Reference Manual Download

Page: 144 / 1510

(default is

), maximum TTL (default is

), and port number (default is

33434

). To

keep the default setting for those parameters, press the ENTER key.
For IPv6, you are prompted for a minimum hop count (default is

) and a maximum

hop count (default is

Example (IPv4)

Dell#traceroute www.Dell Networking.com

Translating "www.Dell Networking.com"...domain server

(10.11.0.1) [OK]

Type Ctrl-C to abort.

-----------------------------------------------

Tracing the route to www.Dell Networking.com (10.11.84.18),

30 hops max, 40 byte packets

-----------------------------------------------

TTL Hostname Probe1 Probe2 Probe3

1 10.11.199.190 001.000 ms 001.000 ms 002.000 ms

2 gwegress-sjc-02.Dell Networking.com (10.11.30.126) 005.000

ms 001.000 ms 001.000 ms

3 fw-sjc-01.Dell Networking.com (10.11.127.254) 000.000 ms

000.000 ms 000.000 ms

4 www.Dell Networking.com (10.11.84.18) 000.000 ms 000.000

ms 000.000 ms

FTOS#

Example (IPv6)

Dell#traceroute 100::1

Type Ctrl-C to abort.

-----------------------------------------------

Tracing the route to 100::1, 64 hops max, 60 byte packets

-----------------------------------------------

Hops Hostname Probe1 Probe2 Probe3

1 100::1 000.000 ms 000.000 ms 000.000 ms

FTOS#traceroute 3ffe:501:ffff:100:201:e8ff:fe00:4c8b

Type Ctrl-C to abort.

-----------------------------------------------

Tracing the route to 3ffe:501:ffff:100:201:e8ff:fe00:4c8b,

64 hops max, 60 byte packets

-----------------------------------------------

Hops Hostname Probe1 Probe2 Probe3

1 3ffe:501:ffff:100:201:e8ff:fe00:4c8b

000.000 ms 000.000 ms 000.000 ms

Dell#

Related
Commands

ping

— tests the connectivity to a device.

144

Control and Monitoring

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands