manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 592 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 592

• VLANs created dynamically with GVRP exist only as long as a GVRP-enabled device is sending 

updates. If the devices no longer send updates, or GVRP is disabled, or the system is rebooted, all 

dynamic VLANs are removed.

• GVRP manages the active topology, not non-topological data such as VLAN protocols. If a local 

bridge must classify and analyze packets by VLAN protocols, manually configure protocol-based 

VLANs, and simply rely on GVRP for VLAN updates. But if the local bridge must know only how to 

reach a given VLAN, then GVRP provides all necessary information.

• The VLAN topologies that GVRP learns are treated differently from VLANs that are statically 

configured. The GVRP dynamic updates are not saved in NVRAM, while static updates are saved in 

NVRAM. When GVRP is disabled, the system deletes all VLAN interfaces that were learned through 

GVRP and leaves unchanged all VLANs that were manually configured.

clear gvrp statistics

Clear GVRP statistics on an interface.

S6000

Syntax

clear gvrp statistics interface 

interface

Parameters

interface 

interface

Enter the following keywords and slot/port or number 
information:

• For a Port Channel interface, enter the keywords 

port-

channel

 then a number. The range is from 1 to 128.

• For a 10-Gigabit Ethernet interface, enter the keyword 

TenGigabitEthernet

 then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword 

fortyGigE

 then the slot/port information.

Defaults

none

Command 
Modes

EXEC

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on C-Series, E-Series, and S-Series

592

GARP VLAN Registration (GVRP)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments