manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 469 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 469

Admin is enabled

TC-grp Priority# Bandwidth TSA

0 0,1,2,3,4,5,6,7 100% ETS

1 0% ETS

2 0% ETS

3 0% ETS

4 0% ETS

5 0% ETS

6 0% ETS

7 0% ETS

Priority# Bandwidth TSA

0 13% ETS

1 13% ETS

2 13% ETS

3 13% ETS

4 12% ETS

5 12% ETS

6 12% ETS

7 12% ETS

Remote Parameters:

-------------------

Remote is disabled

Local Parameters :

------------------

Local is enabled

TC-grp Priority# Bandwidth TSA

0 0,1,2,3,4,5,6,7 100% ETS

1 0% ETS

2 0% ETS

3 0% ETS

4 0% ETS

5 0% ETS

6 0% ETS

7 0% ETS

Priority# Bandwidth TSA

0 13% ETS

1 13% ETS

2 13% ETS

3 13% ETS

4 12% ETS

5 12% ETS

6 12% ETS

7 12% ETS

Oper status is init

Conf TLV Tx Status is disabled

Traffic Class TLV Tx Status is disabled

0 Input Conf TLV Pkts, 0 Output Conf TLV Pkts, 0 Error Conf 

TLV Pkts

0T LIVnput Traffic Class TLV Pkts, 0 Output Traffic Class TLV 

Pkts, 0 Error Traffic

Class

Pkts

Example 
(Detail)

Dell(conf)# show interfaces tengigabitethernet 0/0 ets detail

Interface TenGigabitEthernet 0/0

Max Supported TC Groups is 4

Number of Traffic Classes is 8

Admin mode is on

Admin Parameters :

------------------

Admin is enabled

TC-grp Priority#        Bandwidth TSA

0      0,1,2,3,4,5,6,7  100%      ETS

Data Center Bridging (DCB)

469

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments