Dell Networking S6000 System Reference Manual Download Page 357

Page: 357 / 1510

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Version 7.2.1.0

Introduced.

Usage
Information

This command turns on BGP soft-reconfiguration inbound debugging. If no
neighbor is specified, debug turns on for all neighbors.

debug ip bgp updates

Allows you to view information about BGP updates.

S6000

Syntax

debug ip bgp updates [in | out | prefix-list prefix-list-name]

To disable debugging, use the

no debug ip bgp [

ip-address

| peer-group

peer-group-name

] updates [in | out]

command.

Parameters

(OPTIONAL) Enter the keyword

to view only BGP updates

received from neighbors.

out

(OPTIONAL) Enter the keyword

out

to view only BGP

updates sent to neighbors.

prefix-list

prefix-list-
name

(OPTIONAL) Enter the keyword

prefix-list

then the

name of an established prefix list. If the prefix list is not
configured, the default is

permit

(to allow all routes).

ip-address

(OPTIONAL) Enter the IP address of the neighbor in dotted
decimal format.

peer-group-
name

(OPTIONAL) Enter the name of the peer group to disable or
enable all routers within the peer group.

Command
Modes

EXEC Privilege

Border Gateway Protocol

357

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Dell Networking S6000 System, Reference Manual, Page: 357 / 1510

Search results

Summary of Contents for Networking S6000 System

Reviews: