Dell Networking S6000 System Page 1148 Reference Manual Download | Manualshive

Page: 1148 / 1510

background image

Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g,
wred_teng_y, wred_teng_.

Defaults

When WRED green is applied, default WRED yellow profiles take effect and vice-
versa.

Command
Modes

CONFIGURATION (conf-qos-policy-out)

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Usage
Information

To assign drop precedence to green or yellow traffic, use this command. If there is
no honoring enabled on the input, all the traffic defaults to green drop precedence.

Related
Commands

— creates a WRED profile and name that profile.

— defines the dynamic classification to trust DSCP.

wred ecn

To indicate network congestion, rather than dropping packets, use explicit congestion notification (ECN).

S6000

Syntax

wred ecn

To stop marking packets, use the

no wred ecn

command.

Defaults

none

Command
Modes

CONFIGURATION (conf-qos-policy-out)

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

1148

Quality of Service (QoS)

«
...
1146
1147
1148
1149
1150
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

xStack DGS-3612G series

Brand: D-Link Pages: 546

xStack DGS-3400 Series

Brand: D-Link Pages: 326

xStack DGS-3612G series

Brand: D-Link Pages: 493

xStack DGS-3400 Series

Brand: D-Link Pages: 540

DXS-3326GSR - xStack Switch - Stackable

Brand: D-Link Pages: 354

DGS-1224TP - Web Smart Switch

Brand: D-Link Pages: 52

Brand: D-Link Pages: 8

DES-3225G Series

Brand: D-Link Pages: 3

DES-1228 - Web Smart Switch

Brand: D-Link Pages: 69

Brand: D-Link Pages: 109

Brand: Barco Pages: 2

Brand: Ubisys Pages: 40

Brand: X10 Pages: 20

Brand: H3C Pages: 90

Brand: Hansen Pages: 4

Brand: National Instruments Pages: 23

Brand: Endress+Hauser Pages: 25

Brand: Ruby Tech Pages: 301

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands