manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 1498 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1498

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

pre-Version 
6.2.1.1

Introduced on the E-Series.

disable

Disable a VRRP group.

S6000

Syntax

disable

To re-enable a disabled VRRP group, use the 

no disable

 command.

Command 
Modes

VRRP

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

pre-Version 
6.2.1.1

Introduced on the E-Series.

Usage 
Information

To enable VRRP traffic, assign an IP address to the VRRP group using the 

virtual-address

 command and enter 

no disable

.

Related 
Commands

virtual-address

 — specifies the IP address of the virtual router.

1498

Virtual Router Redundancy Protocol (VRRP)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments