Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 219 / 1510

background image

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 7.4.1.0

Added the

monitor

option.

pre-Version
6.1.1.0

Introduced on the E-Series.

Usage
Information

When you use the

log

option, the CP processor logs details about the packets that

match. Depending on how many packets match the log entry and at what rate, the
CP may become busy as it has to log these packets’ details.

NOTE: When ACL logging and byte counters are configured simultaneously,
byte counters may display an incorrect value. Configure packet counters with
logging instead.

Related
Commands

— configures a filter to drop packets.

— configures a filter to forward packets.

Extended MAC ACL Commands

When an access-list is created without any rule and then applied to an interface, ACL behavior reflects
implicit permit. The following commands configure Extended MAC ACLs.

The S6000 supports both Ingress and Egress MAC ACLs.

NOTE: For more information, also refer to the

Commands Common to all ACL Types

MAC Access List Commands

sections.

deny

To drop packets that match the filter criteria, configure a filter.

S6000

Syntax

deny {any | host

mac-address

|

mac-source-address mac-source-

address-mask

} {any | host

mac-address

|

mac-destination-address

Access Control Lists (ACL)

219

«
...
217
218
219
220
221
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: Cisco Pages: 30

S5800-EI Series

Brand: H3C Pages: 61

Brand: Aruba Pages: 6

Brand: Datavideo Pages: 38

Brand: Ask Pages: 4

Brand: Voith Pages: 98

Brand: Kramer Pages: 33

Brand: Intellinet Pages: 12

Brand: Emos Pages: 44

Brand: TRENDnet Pages: 2

Brand: Foxun Pages: 7

Brand: Kramer Pages: 8

Brand: CONCORD Pages: 18

stiro RWS-211D/N

Brand: Zamel Pages: 11

Brand: Foxtel Pages: 9

Brand: H-Tronic Pages: 20

Brand: HighSecLabs Pages: 4

DG-GS4900SE Series

Brand: Digisol Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands