Dell Networking S6000 System Page 812 Reference Manual Download

Page: 812 / 1510

hostname dynamic

Enables dynamic learning of hostnames from routers in the domain and allows the routers to advertise
the hostname in LSPs.

S6000

Syntax

hostname dynamic

To disable this command, use the

no hostname dynamic

command.

Defaults

Enabled.

Command
Modes

ROUTER ISIS

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version
8.3.12.0

Introduced on the S4810.

Version 8.3.11.1

Introduced on the Z9000.

Usage
Information

To build name-to-systemID mapping tables through the protocol, use this
command. All

show

commands that display systems also display the hostname.

Related
Commands

clns host

— defines a name-to-NSAP mapping.

ignore-lsp-errors

Ignore LSPs with bad checksums instead of purging those LSPs.

S6000

Syntax

ignore-lsp-errors

To return to the default values, use the

no ignore-lsp-errors

command.

Defaults

In IS-IS, the default deletes LSPs with internal checksum errors (

no ignore-lsp-

errors

812

Intermediate System to Intermediate System (IS-IS)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands