Dell Networking S6000 System Reference Manual Download

Page: 747 / 1510

Internet 5.5.5.10 - 00:01:e8:44:99:55 - Vl

10 CP

Internet 10.1.2.4 1 00:01:e8:d5:9e:e2 Ma 0/0

- CP

Internet 10.10.10.4 1 00:01:e8:d5:9e:e2 Ma 0/0

- CP

Internet 10.16.127.53 1 00:01:e8:d5:9e:e2 Ma 0/0

- CP

Internet 10.16.134.254 20 00:01:e8:d5:9e:e2 Ma 0/0

- CP

Internet 133.33.33.4 1 00:01:e8:d5:9e:e2 Ma 0/0

- CP

Usage
Information

The following describes the

show arp summary

command shown in the

following example.

Description

Total Entries

Lists the total number of ARP entries in the ARP table.

Static Entries

Lists the total number of configured or static ARP entries.

Dynamic Entries

Lists the total number of learned or dynamic ARP entries.

CPU

Lists which CPU the entries are stored on.

Example
(Summary)

#show arp summary

TotalEntries Static Entries Dynamic Entries CPU

----------------------------------------------

83 0 83 CP

Dell

Related
Commands

ip local-proxy-arp

— enables/disables Layer 3 communication in secondary VLANs.

switchport mode private-vlan

— sets PVLAN mode of the selected port.

show arp retries

Display the configured number of ARP retries.

S6000

Syntax

show arp retries

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

IPv4 Routing

747

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands