Dell Networking S6000 System Reference Manual Download

Page: 718 / 1510

• For the Management interface, enter the keyword

ManagementEthernet

then the slot/port information.

The slot range is from 0 to 1 and the port range is 0.

• For a Port Channel interface, enter the keywords

port-

channel

then a number. For the C-Series and S-Series,

the range is from 1 to 128.

• For a SONET interface, enter the keyword

sonet

then the

slot/port information.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• For a VLAN, enter the keyword

vlan

then a number from

1 to 4094.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 8.2.1.0

Added support for 4094 VLANs on the E-Series ExaScale (the
prior limit was 2094).

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Added the

access-group

option.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 6.3.1.0

Added the

count

option.

Usage
Information

The following describes the

debug ip packet

command in the following

example.

Field

Description

Lists the source address of the packet and the name of the
interface (in parentheses) that received the packet.

718

IPv4 Routing

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands