manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 1250 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1250

Version 7.5.1.0

Introduced on the C-Series.

pre-Version 
6.2.1.0

Introduced on the E-Series.

ip radius source-interface

Specify an interface’s IP address as the source IP address for RADIUS connections.

S6000

Syntax

ip radius source-interface 

interface

To delete a source interface, use the 

no ip radius source-interface 

command.

Parameters

interface

Enter the following keywords and slot/port or number 
information:

• For a 100/1000 Ethernet interface, enter the keyword 

GigabitEthernet

 then the slot/port information.

• For a Gigabit Ethernet interface, enter the keyword 

GigabitEthernet

 then the slot/port information.

• For Loopback interfaces, enter the keyword 

loopback 

then a number from zero (0) to 16838.

• For the Null interface, enter the keywords 

null 0

.

• For a Port Channel interface, enter the keywords 

port-

channel

 then a number. The range is from 1 to 128.

• For a ten-Gigabit Ethernet interface, enter the keyword 

TenGigabitEthernet

 then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword 

fortyGigE

 then the slot/port information.

• For VLAN interface, enter the keyword 

vlan

 then a 

number from 1 to 4094.

Defaults

Not configured.

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

1250

Security

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments