manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual

Share
Download
Dell Networking S6000 System Reference Manual Download Page 165

• For a Gigabit Ethernet interface, enter the keyword 

GigabitEthernet

 then the slot/port information.

• For a Fast Ethernet interface, enter the keyword 

FastEthernet

 then the slot/port information.

• For a Ten-Gigabit Ethernet interface, enter the keyword 

TenGigabitEthernet

 then the slot/port information.

mac-address

(Optional) MAC address of an 802.1X-authenticated 
supplicant.

Defaults

none

Command 
Modes

• EXEC
• EXEC privilege

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.0.0.0

Introduced on the Z9000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 
8.3.12.0

Introduced on the S4810.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.4.2.1

Introduced on the C-Series and S-Series.

Usage 
Information

Enter a supplicant’s MAC address using the 

mac-address

 option to display CoS 

mapping information only for the specified supplicant.

You can display the CoS mapping information applied to traffic from authenticated 
supplicants on 802.1X-enabled ports that are in Single-Hot, Multi-Host, and Multi-
Supplicant authentication modes.

Example

Dell#show dot1x cos-mapping interface gigabitethernet 2/21

802.1p CoS re-map table on Gi 2/21:

----------------------------------

Dot1p   Remapped Dot1p

0       7

1       6

2       5

3       4

4       3

5       2

6       1

7       0

802.1X

165

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands