Dell Networking S6000 System Reference Manual Download

Page: 1075 / 1510

Field

Description

Incoming
interface

Displays the reverse path forwarding (RPF) interface towards
the RP/ source.

RPF neighbor

Displays the next hop from this interface towards the RP/
source.

Outgoing
interface list:

Lists the interfaces that meet one of the following criteria:

• a directly connect member of the Group
• statically configured member of the Group
• received a (*,G) Join message

Example

Dell#show ip pim tib

PIM Multicast Routing Table

Flags:D- Dense, S- Sparse, C- Connected, L- Local, P- Pruned,

R- RP-bit set, F- Register flag, T- SPT-bit set, J- Join

SPT,

M- MSDP created entry, A- Candidate for MSDP

Advertisement,

K- Ack-Pending State

Timers: Uptime/Expires

Interface state: Interface, next-Hop, State/Mode

(*, 226.1.1.1), uptime 01:29:19, expires 00:00:52, RP

10.211.2.1, flags: SCJ

Incoming interface: GigabitEthernet 4/23, RPF neighbor

10.211.1.2

Outgoing interface list:

GigabitEthernet 8/0

(*, 226.1.1.2), uptime 00:18:08, expires 00:00:52, RP

10.211.2.1, flags: SCJ

Incoming interface: GigabitEthernet 4/23, RPF neighbor

10.211.1.2

Outgoing interface list:

GigabitEthernet 8/0

(*, 226.1.1.3), uptime 00:18:08, expires 00:00:52, RP

10.211.2.1, flags: SCJ

Incoming interface: GigabitEthernet 4/23, RPF neighbor

10.211.1.2

Outgoing interface list:

GigabitEthernet 8/0

(*, 226.1.1.4), uptime 00:18:08, expires 00:00:52, RP

10.211.2.1, flags: SCJ

Incoming interface: GigabitEthernet 4/23, RPF neighbor

10.211.1.2

Outgoing interface list:

GigabitEthernet 8/0

PIM-Sparse Mode (PIM-SM)

1075

«
...
1073
1074
1075
1076
1077
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands