manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 568 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 568

Version 
8.3.19.0

Introduced on the S4820T.

Version 
8.3.12.0

Introduced on the S4810.

fip-snooping enable

Enable FIP snooping on all VLANs or on a specified VLAN.

Syntax

fip-snooping enable

To disable the FIP snooping feature on all or a specified VLAN, use the 

no fip-

snooping enable

 command.

Defaults

FIP snooping is disabled on all VLANs.

Command 
Modes

• CONFIGURATION
• VLAN INTERFACE

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 
8.3.19.0

Introduced on the S4820T.

Version 
8.3.12.0

Introduced on the S4810.

Usage 
Information

The maximum number of FCFs supported per FIP snooping-enabled VLAN is four. 
The maximum number of FIP snooping sessions supported per ENode server is 16.

fip-snooping fc-map

Configure the FC-MAP value FIP snooping uses on all VLANs.

Syntax

fip-snooping fc-map 

fc-map-value

To return the configured FM-MAP value to the default value, use the 

no fip-

snooping fc-map

 command.

568

FCoE Transit

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments