Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 281 / 1510

background image

Parameters

log

(OPTIONAL) Enter the keyword

log

to enable the triggering

of ACL log messages.

threshold-in
msgs

count

(OPTIONAL) Enter the

threshold-in-msgs

keyword

followed by a value to indicate the maximum number of ACL
logs that can be generated, exceeding which the generation
of ACL logs is terminated with the

seq

,

permit

, or

deny

commands. The threshold range is from 1 to 100.

interval

minutes

(OPTIONAL) Enter the keyword

interval

followed by the

time period in minutes at which ACL logs must be generated.
The interval range is from 1 to 10 minutes.

monitor

(OPTIONAL) Enter the keyword

monitor

when the rule is

describing the traffic that you want to monitor and the ACL
in which you are creating the rule is applied to the monitored
interface.

Defaults

By default, 10 ACL logs are generated if you do not specify the threshold explicitly.

The default frequency at which ACL logs are generated is five minutes. By default,
flow-based monitoring is not enabled.

Command
Modes

CONFIGURATION-MAC ACCESS LIST-STANDARD

Command
History

Version 9.4(0.0)

Added support for flow-based monitoring on the S4810,
S4820T, S6000, and Z9000 platforms.

Version 9.3(0.0)

Added support for logging of ACLs on the S4810, S4820T,
and Z9000 platforms.

Usage
Information

When the configured maximum threshold is exceeded, generation of logs is
stopped. When the interval at which ACL logs are configured to be recorded
expires, the subsequent, fresh interval timer is started and the packet count for that
new interval commences from zero. If ACL logging was stopped previously
because the configured threshold is exceeded, it is re-enabled for this new interval.

If ACL logging is stopped because the configured threshold is exceeded, it is re-
enabled after the logging interval period elapses. ACL logging is supported for
standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure
ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable
logging for ACLs that are associated with egress interfaces.

You can activate flow-based monitoring for a monitoring session by entering the

flow-based enable

command in the Monitor Session mode. When you enable

this capability, traffic with particular flows that are traversing through the ingress
and egress interfaces are examined and, appropriate ACLs can be applied in both
the ingress and egress direction. Flow-based monitoring conserves bandwidth by
monitoring only specified traffic instead all traffic on the interface. This feature is
particularly useful when looking for malicious traffic. It is available for Layer 2 and
Layer 3 ingress and egress traffic. You may specify traffic using standard or
extended access-lists. This mechanism copies all incoming or outgoing packets on

Access Control Lists (ACL)

281

«
...
279
280
281
282
283
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: I-Tech Pages: 27

Brand: ABB Pages: 10

Brand: Cole Hersee Pages: 2

Digital Energy STS-400-25-3

Brand: GE Pages: 49

Brand: Ruby Tech Pages: 254

Brand: Jerguson Pages: 4

Brand: Lancom Pages: 21

Brand: Racal Instruments Pages: 53

Brand: Madison Pages: 2

Brand: H3C Pages: 96

Brand: NVision Pages: 86

Brand: DataParts Pages: 5

Brand: Edge-Core Pages: 60

Brand: steute Pages: 10

Brand: DANLERS Pages: 2

Brand: Eaton Pages: 12

BOCAHUB-16 Plus BEN220

Brand: Boca Pages: 56

Brand: Alloy Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands