manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 928 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 928

Parameters

peer address

Enter the peer address in a dotted decimal format (A.B.C.D.)

list 

name

Enter the keywords 

list name

 and specify a standard 

access list that contains the RP address that should be 
treated as the default peer. If no access list is specified, then 
all SAs from the peer are accepted.

Defaults

Not configured.

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Added the 

list

 option and removed the 

prefix-list 

option.

Version 7.4.1.0

Introduced

Usage 
Information

If a list is not specified, all SA messages received from the default peer are 
accepted. You can enter multiple 

default peer

 commands.

ip msdp log-adjacency-changes

Enable logging of MSDP adjacency changes.

S6000

Syntax

ip msdp log-adjacency-changes

To disable logging, use the 

no ip msdp log-adjacency-changes

 command.

Defaults

Not configured.

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

928

Multicast Source Discovery Protocol (MSDP)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments