Dell Networking S6000 System Reference Manual Download Page 382

Page: 382 / 1510

When you remove all clients of a route reflector using the

no neighbor route-

reflector-client

command, the router no longer functions as a route

reflector.

If the clients of a route reflector are fully meshed, you can configure the route
reflector to not reflect routes to specified clients by using the

no bgp client-

to-client reflection

command.

This command automatically restarts the neighbor session for the configuration to
take effect.

Related
Commands

bgp client-to-client reflection

— enables route reflection between the route

reflector and the clients.

neighbor shutdown

Disable a BGP neighbor or peer group.

S6000

Syntax

neighbor {

ip-address

peer-group-name

} shutdown

To enable a disabled neighbor or peer group, use the

neighbor {

ip-address

peer-group-name

}no shutdown

command.

Parameters

ip-address

Enter the IP address of the neighbor in dotted decimal
format.

peer-group-
name

Enter the name of the peer group to disable or enable all
routers within the peer group.

Defaults

Enabled (that is, BGP neighbors and peer groups are disabled.)

Command
Modes

ROUTER BGP

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

382

Border Gateway Protocol

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Dell Networking S6000 System, Reference Manual, Page: 382 / 1510

Search results

Summary of Contents for Networking S6000 System

Reviews: