Dell Networking S6000 System Reference Manual Download Page 714

Page: 714 / 1510

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 8.2.1.0

Added support for 4094 VLANs on the E-Series ExaScale (the
prior limit was 2094).

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 6.3.1.0

Added the

count

option.

Usage
Information

To stop packets from flooding the user terminal when debugging is turned on, use
the

count

option.

debug ip dhcp

Enable debug information for dynamic host configuration protocol (DHCP) relay transactions and display

the information on the console.

S6000

Syntax

debug ip dhcp

To disable debug, use the

no debug ip dhcp

command.

Defaults

Debug disabled

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

714

IPv4 Routing

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Dell Networking S6000 System, Reference Manual, Page: 714 / 1510

Search results

Summary of Contents for Networking S6000 System

Reviews: