manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 1151 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1151

Version 8.3.7.0

Introduced on the S4810.

Usage 
Information

Use the default pre-defined profiles or configure your own profile. You cannot 
delete the pre-defined profiles or their default values. This command enables 
WRED configuration mode —(conf-wred).

Related 
Commands

threshold

 — specifies the minimum and maximum threshold values of the WRED 

profile.

rate shape

Define the rate-shaping method to be either as a measure of bytes or packets for each of the hierarchical 

QoS (HQoS) nodes at the leaf level to be applied to each queue.

S6000

Syntax

[no] rate-shape [kbps | pps] peak-rate [

burst-KB/Packets

] 

[committed [kbps | pps] committed-rate [

burst-KB/Packets

]]

Parameters

kbps

Enter the keyword kbps to specify the committed rate limit in 
Kilobits per second (Kbps). Specify this value as a multiple of 
64. The range is from 0 to 40000000. The default granularity 
is Megabits per second (Mbps).

pps

Enter the keyword pps to specify the committed rate limit in 
packets per second (pps). The range is from 1 to 268000000. 
The default granularity is Megabits per second (Mbps).

committed-
rate 

Define the committed rate, which is the guaranteed or 
minimum confirmed rate for the packets. Specify this value 
as a multiple of 64 if you specify the committed rate in Kbps. 
The range is from 0 to 40000000 for Kbps. The range is 
from 1 to 268000000 for pps. The range is from 0 to 40000 
for Mbps (which is the default measure for rate limits if you 
do not explicitly configure Kbps or pps)

burst-KB

(OPTIONAL) Enter the committed burst size in KB. The range 
is from 0 to 10000. The default is 50 KB. The default peak 
burst is regarded as the same value as the configured 
committed burst size.

Packets 

(OPTIONAL) Enter the committed burst size as a count of 
packets. The range is from 1 to 1073000. The default is 50 
packets. The default peak rate is regarded as the same value 
as the configured committed rate.

peak-rate 

Define the peak rate, which is the guaranteed or minimum 
confirmed rate for the packets. Specify this value as a 
multiple of 64 if you specify the peak rate in Kbps. The range 
is from 0 to 40000000 for Kbps. The range is from 1 to 
268000000 for pps. The range is from 0 to 40000 for Mbps 
(which is the default measure for rate limits if you do not 
explicitly configure Kbps or pps)

Quality of Service (QoS)

1151

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments