Dell Networking S6000 System Page 694 Reference Manual Download

Page: 694 / 1510

Example

Dell(conf)#int port-channel 2

Dell(conf-if-po-2)#

Related
Commands

channel-member

— adds a physical interface to the LAG.

interface

— configures a physical interface.

interface loopback

— configures a Loopback interface.

interface null

— configures a null interface.

interface vlan

— configures a VLAN.

shutdown

— disables/enables the port channel.

minimum-links

Configure the minimum number of links in a LAG (Port Channel) that must be in “oper up” status for the

LAG to be also in “oper up” status.

S6000

Syntax

minimum-links

number

Parameters

number

Enter the number of links in a LAG that must be in “oper up”
status. The range is from 1 to 16. The default is

number

Enter the number of links in a LAG that must be in “oper up”
status. The range is from 1 to 8. The default is

Defaults

Command
Modes

INTERFACE

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

694

Interfaces

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands