manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 650 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 650

interface vlan

Configure a VLAN. You can configure up to 4094 VLANs.

S6000

Syntax

interface vlan 

vlan-id

 [of-instance{

of-id

}]

Syntax

interface vlan 

vlan-id 

Parameters

vlan-id

Enter a number as the VLAN Identifier. The range is from 1 to 
4094.

of-instance{

of-

id

}

Enter the keyword 

of-instance

 then the OpenFlow instance 

ID to add the VLAN to the specified OpenFlow instance. The 
range is from 1 to 8.

NOTE: Associate the OpenFlow instance with the VLAN 
when the VLAN is created. An existing VLAN cannot be 
associated with an OpenFlow instance.

Defaults

Not configured, except for the Default VLAN, which is configured as VLAN 1.

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.1.
(0.0)

Introduced on the S4810; added support for OpenFlow.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Usage 
Information

For more information about VLANs and the commands to configure them, refer to 
the 

Virtual LAN (VLAN) Commands

 section of the 

Layer 2

 chapter.

FTP, TFTP, and SNMP operations are not supported on a VLAN. MAC ACLs are not 
supported in VLANs. IP ACLs are supported. For more information, refer to the 

Access Control Lists (ACL)

 chapter.

The following features are not supported on VLANs associated with an OpenFlow 
instance:

• IPv4
• IPv6

650

Interfaces

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments