Dell Networking S6000 System Page 641 Reference Manual Download

Page: 641 / 1510

gigabitethernet 0/1 - 5

;

interface group

gigabitethernet 0/1-5

• For a Gigabit Ethernet interface, enter the keyword

gigabitethernet

then the slot/port information.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• For a VLAN interface, enter the keyword

vlan

then a

number from 1 to 4094.

Command
Modes

CONFIGURATION

Command
History

Version 9.4(0.0)

Introduced on the S4810, S4820T, S6000, Z9000, and MXL
Switch.

Usage
Information

The

interface group

command will create all the non-existent VLANs specified

in the range. On successful command execution, the CLI switches to the interface
group context.

The configuration commands inside the group context will be the similar to that of
the existing range command.

Note: For release 9.4(0.0), the group command is supported only for VLANs and
physical interfaces.

Example

Dell(conf)#interface group ?

fortyGigE FortyGigabit Ethernet interface

gigabitethernet GigabitEthernet interface IEEE 802.3z

tengigabitethernet TenGigabit Ethernet interface

vlan VLAN keyword

Dell(conf)# interface group vlan 1 - 2 , tengigabitethernet

0/0

Dell(conf-if-group-vl-1-2,te-0/0)# no shutdown

Dell(conf-if-group-vl-1-2,te-0/0)# end

interface loopback

Configure a Loopback interface.

S6000

Syntax

interface loopback

number

To remove a loopback interface, use the

no interface loopback

number

command.

Interfaces

641

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands