Dell Networking S6000 System Page 236 Reference Manual Download

Page: 236 / 1510

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

pre-Version
6.1.1.0

Introduced on the E-Series.

Related
Commands

set community

— specifies a COMMUNITY attribute.

match interface

To match routes whose next hop is on the interface specified, configure a filter.

S6000

Syntax

match interface

interface

To remove a match, use the

no match interface

interface

command.

Parameters

interface

Enter the following keywords and slot/port or number
information:

• .
• For the loopback interface, enter the keyword

loopback

then a number from zero (0) to 16383.

• For a Port Channel interface, enter the keyword

port-

channel

then a number. The range is from 1 to 128.

• For a SONET interface, enter the keyword

sonet

then the

slot/port information.

• For a Ten Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• For a VLAN, enter the keyword

vlan

then a number from

1 to 4094 (you can use IDs 1 to 4094).

236

Access Control Lists (ACL)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands