manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 887 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 887

Defaults

All interfaces in Layer 2 mode are untagged.

Command 
Modes

INTERFACE VLAN

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

pre-Version 
6.2.1.1

Introduced on the E-Series.

Usage 
Information

Untagged interfaces can only belong to one VLAN.

In the Default VLAN, you cannot use the 

no untagged interface

 command. To 

remove an untagged interface from all VLANs, including the Default VLAN, enter 
INTERFACE mode and use the 

no switchport

 command.

Related 
Commands

interface vlan

 — configures a VLAN.

tagged

 — specifies which interfaces in a VLAN are tagged.

Far-End Failure Detection (FEFD)

The Dell Networking operating software supports far-end failure detection (FEFD) on the Ethernet 

interfaces of the S6000platform.
The FEFD feature detects and reports far-end link failures.

• FEFD is not supported on the Management interface.
• During an RPM failover, FEFD is operationally disabled for approximately 8 to 10 seconds.
• By default, FEFD is disabled.

Layer 2

887

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments