Dell Networking S6000 System Reference Manual Download Page 617

Page: 617 / 1510

Version 7.5.1.0

Introduced on the E-Series.

show ip igmp groups

View the IGMP groups.

S6000

Syntax

show ip igmp groups [group-address [detail] | detail |

interface

[

group-address

[detail]]]

Parameters

group-address

(OPTIONAL) Enter the group address in dotted decimal
format to view information on that group only.

interface

(OPTIONAL) Enter the interface type and slot/port
information:

• For a Port Channel interface, enter the keywords

port-

channel

then a number. The range is from 1 to 128.

• For a Loopback interface, enter the keyword

loopback

then a number from 0 to 16383.

• For a 100/1000 Ethernet interface, enter the keyword

gigabitethernet

followed by the slot/port

information.

• For a 1-Gigabit Ethernet interface, enter the keyword

gigabitethernet

followed by the slot/port

information.

• For a 10-Gigabit Ethernet interface, enter the keyword

tengigabitethernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• For a VLAN interface enter the keyword

vlan

then a

number from 1 to 4094.

detail

(OPTIONAL) Enter the keyword

detail

to display the

IGMPv3 source information.

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Internet Group Management Protocol (IGMP)

617

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Dell Networking S6000 System, Reference Manual, Page: 617 / 1510

Search results

Summary of Contents for Networking S6000 System

Reviews: