Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 785 / 1510

background image

• L3 ACL (ipv4acl:

1

• IPv6 L3 ACL (ipv6acl):

2

l2acl

1-4

ipv4acl

1- 4

ipv6acl

0-4

Allocate space to support IPv6 ACLs. Enter all of the profiles
and a range. Enter the CAM profile name then the amount to
be allotted. The total space allocated must equal 4. The

ipv6acl

range must be a factor of 2.

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.4.2.0

Introduced on the E-Series TeraScale.

Version 8.2.1.0

Introduced on the S-Series.

Version 7.8.1.0

Introduced on the C-Series.

Usage
Information

For the new settings to take effect, save the new CAM settings to the startup-
config (

write-mem

or

copy run start

), then reload the system.

The total amount of space allowed is 4 FP Blocks.

Example

Dell#

Dell#configure

Dell(conf)#cam-acl-egress ?

default Reset Egress CAM ACL entries to default setting

l2acl Set L2-ACL entries

Dell(conf)#cam-acl-egress l2acl ?

<1-4> Number of FP blocks for l2acl

Dell(conf)#cam-acl-egress l2acl 1 ?

ipv4acl Set IPV4-ACL entries

Dell(conf)#cam-acl-egress l2acl 1 ipv4acl 1 ?

ipv6acl Set IPV6-ACL entries

Dell(conf)#cam-acl-egress l2acl 1 ipv4acl 1 ipv6acl ?

<0-4> Number of FP blocks for IPV6 (multiples of 2)

Dell(conf)#cam-acl-egress l2acl 1 ipv4acl 1 ipv6acl 2

IPv6 Access Control Lists (IPv6 ACLs)

785

«
...
783
784
785
786
787
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: Camozzi Pages: 2

OfficeConnect 5

Brand: 3Com Pages: 2

OfficeConnect 3C1670500C

Brand: 3Com Pages: 18

Brand: StarTech.com Pages: 2

Brand: Edge-Core Pages: 9

Brand: Erbe Pages: 118

Brand: SMART Pages: 46

Brand: Sangamo Pages: 2

Brand: VeEX Pages: 22

RMQ-Titan M22-LED Series

Brand: Eaton Pages: 4

Brand: Microsens Pages: 8

Brand: Pathway connectivity solutions Pages: 34

Brand: Radware Pages: 4

Brand: Inline Pages: 4

Brand: ATEN Pages: 16

Brand: IRT Electronics Pages: 17

Brand: Audioplex Pages: 8

Brand: Uniclass Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands