Dell Networking S6000 System Reference Manual Download

Page: 1471 / 1510

-------------------------

L2 Total MAC-Address Count :

IGMP MRouter Vlans count :

IGMP Mcast Groups count :

ARP entries count :

Example
(igmp-snoop)

Dell# show vlt counter igmp-snoop

Total IGMP VLT counters

----------------------

IGMP MRouter Vlans count : 1

IGMP Mcast Groups count : 5

Example
(igmp-snoop
interface port-
channel)

Dell#show vlt counter igmp-snoop interface port-channel 2

VLT Port-ID: 2 IGMP Counter

-----------------------

IGMP MRouter Vlans count : 0

IGMP Mcast Groups count : 5

Dell# show vlt counter igmp-snoop interface port-channel 100

VLT Port-ID: 100 IGMP Counter

-----------------------

IGMP MRouter Vlans count : 1

IGMP Mcast Groups count : 0

Example (NDP
and Non-VLT
ARP)

Dell#show vlt counters

Total VLT Counters

-------------------

L2 Total MAC-Address Count: 2

Total Arp Entries Learnt : 0

Total Arp Entries Synced : 0

Total Non-VLT Arp entries Learnt: 0

Total Non-VLT Arp Entries Synced 0

IGMP MRouter Vlans count :

IGMP Mcast Groups count :

Total VLT Ndp Entries Learnt : 2

Total VLT Ndp Entries Synced : 0

Total Non-VLT Ndp Entries Learnt : 0

Total Non-VLT Ndp Entries Synced : 0

show vlt detail

Displays detailed status information about VLT domains currently configured on the switch.

S6000

Syntax

show vlt detail

Default

Not configured.

Command
Modes

EXEC

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

Virtual Link Trunking (VLT)

1471

«
...
1469
1470
1471
1472
1473
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands