Dell Networking S6000 System Page 1095 Reference Manual Download

Page: 1095 / 1510

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 6.4.1.0

Expanded to display port error disable state (EDS) caused by
loopback BPDU inconsistency and Port VLAN ID
inconsistency.

Version 6.2.1.1

Introduced.

Usage
Information

The following describes the

show spanning-tree pvst

command shown in the

following examples.

Field

Description

Interface Name

PVST interface.

Instance

PVST instance.

Sts

Port state: root-inconsistent (INCON Root), forwarding
(FWD), listening (LIS), blocking (BLK), or shut down (EDS
Shut).

Guard Type

Type of STP guard configured (Root, Loop, or BPDU guard).

Example (Brief)

Dell#show spanning-tree pvst vlan 3 brief

VLAN 3

Executing IEEE compatible Spanning Tree Protocol

Root ID Priority 4096, Address 0001.e801.6aa8

Root Bridge hello time 2, max age 20, forward delay 15

Bridge ID Priority 16384, Address 0001.e805.e306

Configured hello time 2, max age 20, forward delay 15

Interface Designated

Name PortID Prio Cost Sts Cost Bridge ID PortID

----------------------------------------------------------

Gi 1/0 128.130 128 20000 FWD 20000 4096 0001.e801.6aa8

128.426

Gi 1/1 128.131 128 20000 BLK 20000 4096 0001.e801.6aa8

128.427

Gi 1/16 128.146 128 20000 FWD 20000 16384 0001.e805.e306

128.146

Gi 1/17 128.147 128 20000 FWD 20000 16384 0001.e805.e306

128.147

Interface

Name Role PortID Prio Cost Sts Cost Link-type Edge

-----------------------------------------------------

Gi 1/0 Root 128.130 128 20000 FWD 20000 P2P No

Gi 1/1 Altr 128.131 128 20000 BLK 20000 P2P No

Gi 1/16 Desg 128.146 128 20000 FWD 20000 P2P Yes

Gi 1/17 Desg 128.147 128 20000 FWD 20000 P2P Yes

Example

Dell#show spanning-tree pvst vlan 2

VLAN 2

Root Identifier has priority 4096, Address 0001.e805.e306

Root Bridge hello time 2, max age 20, forward delay 15

Bridge Identifier has priority 4096, Address 0001.e805.e306

Configured hello time 2, max age 20, forward delay 15

We are the root of VLAN 2

Current root has priority 4096, Address 0001.e805.e306

Per-VLAN Spanning Tree Plus (PVST+)

1095

«
...
1093
1094
1095
1096
1097
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands